COMMONWEALTH OF AUSTRALIA DISCUSSION

COMMONWEALTH OF AUSTRALIA DISCUSSIONCOMMONWEALTH OF AUSTRALIACopyright Regulations 1969
WarningThis material has been reproduced and communicated to you by or on behalf of The Charles Darwin University pursuant to Part VB of the Copyright Act 1968 (the Act). The material in this communication may be subject to copyright under the Act. Any further reproduction or communication of this material by you may be the subject of copyright protection under the Act.Do not remove this notice( Semester 2, 2016 FINAL EXAMINATION DURATION HIT274 – Network Engineering Applications Teaching Period Student Number Given Names Family Name Reading Time: 10 minutes Writing Time: 180 minutes )INSTRUCTIONS TO CANDIDATESThe examination has 3 sectionsSection A:Suggested Time:Multiple Choice Questions: Answer ALL questions45 minutes (30 marks)Section B:Suggested Time:Short Answer Questions: Answer ALL questions95 minutes (50 marks)Section B:Suggested Time:Case Study: Answer ALL questions40 minutes (20 marks)Questions in section A must be answered directly onto the Examination Paper. Section B and C are to be answered in the booklets provided.Note that questions ARE NOT of equal value.EXAM CONDITIONSYou may begin writing from the commencement of the examination session. The reading time indicated above is provided as a guide only.This is a CLOSED BOOK examination No calculators are permittedNo handwritten notes are permitted No dictionaries are permittedADDITIONAL AUTHORISED MATERIALSEXAMINATION MATERIALS TO BE SUPPLIEDNo additional printed material is permitted1 x 16 Page Book 1 x Scrap Paper( THIS EXAMINATION PAPER AND SUPPLIED MATERIALS ARE NOT PERMITTED TO BE REMOVED FROM ANY EXAMINATION VENUE IN ANY CIRCUMSTANCE. THIS EXAMINATION IS PRINTED DOUBLE-SIDED. )Semester 2, 2016 FINAL EXAMINATIONHIT274 – Network Engineering ApplicationsPage 1 of 10THIS EXAMINATION IS PRINTED DOUBLE-SIDED.
THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK.Semester 2, 2016 FINAL EXAMINATIONHIT274 – Network Engineering ApplicationsPage 2 of 10Section A Multiple Choice Questions
Total No of Marks for this section: 30
This section should be answered directly into this booklet by placing an X next to your chosen answers. Please ensure that your name and student number have been written on this booklet.Each question is worth 1 mark.Suggested Time allocation for Section A: 45 minsSemester 2, 2016 FINAL EXAMINATIONHIT274 – Network Engineering ApplicationsPage 3 of 10Section B
Short Answer QuestionsTotal No of Marks for this section: 50
This section should be answered in the Answer Booklet provided.Marks for each question are indicated.Suggested Time allocation for Section B: 95 minsQuestion 1
Complete the table below:Full IPv6Abbreviated IPv6aFE80:0000:0000:0400:0000:0000:0000:054Afe80:0:0:400::54ab4:b200:80:f0a:5000:c:885:a0004:B200:80:F0A:5000:C:885:A000c0C00:00B8:2001:0000:0000:0000:0000:0DB8c00:b8:2001::db8(3 marks)Question 2
Complete the table belowAddress / lengthPrefixa4EDF:400:0:50A:FACE:BAFF:FE00:0/96bD001:F0:E:D3F2:FACE:BAFF:FE00:0/72cD234::CAFE:F0A0:BAFF:FE00:0/62(3 marks)Semester 2, 2016 FINAL EXAMINATIONHIT274 – Network Engineering ApplicationsPage 4 of 10Question 3a. What is the summary route to reach HQ LANs?b. What is the summary route to reach Branch1 LANs?c. What is the summary route to reach Branch2 LANs?d. What is the summary route from the ISP router to reach all LANs?(8 marks)Question 4
Given the IP address of 138.152.192.0/22, allocate IP address to the following groups using VLSM.· Group A: 600 users· Group B: 400 users· Group C: 200 users· Group D: 50 users· Group E: 4 usersAnswer the following questions:a. What is the last usable host address and subnet mask (in dotted decimal notation) of group A?b. What is the first usable host address and subnet mask (in dotted decimal notation) of group C?c. What is the broadcast address and subnet mask (in dotted decimal notation) of group D?d. How many unallocated addresses are there?(8 marks)Semester 2, 2016 FINAL EXAMINATIONHIT274 – Network Engineering ApplicationsPage 5 of 10Question 5
When do you use static routing?(3 marks)Question 6
Write down two advantages and two disadvantages of static routing.(4 marks)Question 7The legacy inter-VLAN routing is shown. Answer the following questions:a. What are the disadvantages of such a setup?b. What is a better alternative? Draw diagram to illustrate.c. What additional configurations are needed for such alternative setup?(6 marks)Question 8
State why it is a good practice to configure passive interfaces(3 marks)Semester 2, 2016 FINAL EXAMINATIONHIT274 – Network Engineering ApplicationsPage 6 of 10Question 9
Explain the use of the following commands:a. switchport port-securityb. switchport port-security maximum(2 marks)Question 10
Compare the differences between NAT and PAT.(4 marks)Question 11This network is meant to have the following three policies implemented:· Hosts from the 192.168.0.0/24 network are unable to access any TCP service of Server3but should not be otherwise restricted· Hosts from the 10.0.0.0/8 network are unable to access the HTTP service of Server1 but should not be otherwise restricted· Hosts from the 172.16.0.0/16 network are unable to access the FTP service of Server2but should not be otherwise restricted Part of the running configuration for R1 is shown.Semester 2, 2016 FINAL EXAMINATIONHIT274 – Network Engineering ApplicationsPage 7 of 10Can you state the problems with the given configurations and suggest what can be done to rectify the problems?(6 marks)Semester 2, 2016 FINAL EXAMINATIONHIT274 – Network Engineering ApplicationsPage 8 of 10Section C Case Study
Total Number of Marks for this section: 20
This section should be answered in the Answer Booklet provided.Marks for each question are indicated.Suggested Time allocation for Section C: 40 minsA topology is set up with some information given below:· The “show ip route” information for router 2 and router 3 are given.· There are only 3 routers in this topology.· IP addresses of some devices in the topology are also givenRouter 2
Router 3Semester 2, 2016 FINAL EXAMINATIONHIT274 – Network Engineering ApplicationsPage 9 of 10The information about some of the devices is shown in the table below:DeviceInterfaceIP AddressSubnet MaskDefault GatewayRouter 1G0/0N/AS0/0/0172.16.3.1N/AS0/0/1192.168.10.5N/ARouter 2G0/0172.16.2.1255.255.255.0N/AS0/0/0N/AS0/0/1192.168.10.9N/ARouter 3G0/0192.168.1.1255.255.255.0N/AS0/0/0192.168.10.6N/AS0/0/1N/APC1NIC255.255.255.0172.16.1.1PC2NIC255.255.255.0PC3NIC192.168.1.2255.255.255.01. Based on all the given information, draw the topology of the setup, clearly identifying the LANs, the type of cable used and the connections between the routers. The IP address and the prefix for each network are to be shown clearly in the diagram.(8 marks)2. Complete the given table above.(7 marks)3. What would be the path taken by a ping froma. PC 1 to PC 3? Would it be different if RIP was configured instead?b. PC 2 to PC 3? Would it be different if RIP was configured instead?(5 marks)Semester 2, 2016 FINAL EXAMINATIONHIT274 – Network Engineering ApplicationsPage 10 of 10